Mentor Graphics Design and Verification Tools Certified for TSMC 16nm FinFET Production

Author
SySAdmin
Posted
April 15, 2014
Views
1155

Page All:

Page 1
Mentor Graphics Design and Verification Tools Certified for TSMC 16nm FinFET Production

WILSONVILLE, Ore., April 15, 2014 /PRNewswire/ -- Mentor Graphics Corp. (NASDAQ: MENT) today announced that its IC design to silicon solution has achieved certification for TSMC's Design Rule Manual (DRM) and SPICE model version 1.0 for its 16nm FinFET process. The certification includes tools in the Calibre® physical verification and design-for-manufacturing (DFM) platform, as well as the Olympus-SoC(TM) place and route system, the Pyxis(TM) custom IC design platform, and Eldo® SPICE simulator. Mentor also successfully demonstrated a complete 16nm FinFET digital flow using the Olympus-SoC and Calibre products and the ARM® Cortex®-A15 MPCore processor as the validation vehicle. The Mentor 16nm solutions are available now to support customers as they transition from test chips to full production 16nm FinFET design efforts.

http://photos.prnewswire.com/prnvar/20140317/AQ83812LOGO

The Olympus-SoC place and route system enables efficient design closure with complete support for all 16nm FinFET double patterning (DP), DRC and DFM rules, fin grid alignment for macros and standard cells, and Vt min-area rules support. The new flow also supports low-voltage hold time fixing, interconnect resistance minimization, signal EM fixing, MiM Cap extraction to address timing impact, and enhanced pin accessibility and routability.

The Calibre nmDRC(TM) platform supports design teams to ensure their designs meet process requirements.  The SmartFill capability in Calibre YieldEnhancer, along with the other Mentor DFM products, Calibre LFD(TM) and Calibre CMPAnalyzer, were enhanced to meet TSMC-specified requirements for filling, lithography, and CMP simulations for 16FF.

The TSMC 16nm design kit offering for Mentor provides reliability checks based on the Calibre PERC(TM) product. This enables customers to analyze and correct issues like electrostatic discharge (ESD) and latch-up at both IP and full chip level using a common platform and set of checks regardless of the IP source.

To ensure accurate circuit simulation of FinFET devices, Mentor collaborated with TSMC on enhancement and certification of the high-performance Calibre xACT(TM) 2.5D and 3D extraction product, and FinFET device models in the Calibre nmLVS(TM) product.

The Pyxis custom IC design platform is extended to handle fin grids and provide a fin grid display, and to support guard rings, MOS abutment rules and design rule-driven (DRD) layout. The Eldo simulator has been upgraded to provide accurate FinFET device and circuit level modeling based on the latest BSIM-CMG and TMI models from TSMC.

"We've worked closely with TSMC to ensure our tools are ready for 16nm FinFET technology, including ongoing efforts with TSMC to optimize Calibre rule decks for the best turnaround time," said Joseph Sawicki, vice president and general manager of the Design to Silicon division at Mentor Graphics. "By jointly evolving our products to handle 16nm FinFET requirements, we minimize the learning curve and allow designers to leverage TSMC's offering to create differentiated value in their products."

"The longstanding working relationship between TSMC and Mentor has allowed us to address the design requirements of 16nm FinFET, while continuing to deliver production ready solutions against an aggressive technology roadmap," said Suk Lee, TSMC senior director, Design Infrastructure Marketing Division. "At each new node we are proving once again that ecosystem collaboration under Open Innovation Platform is critical to driving innovation for the semiconductor design industry."

About Mentor Graphics
Mentor Graphics Corporation is a world leader in electronic hardware and software design solutions, providing products, consulting services and award-winning support for the world's most successful electronic, semiconductor and systems companies. Established in 1981, the company reported revenues in the last fiscal year in excess of $1.15 billion. Corporate headquarters are located at 8005 S.W. Boeckman Road, Wilsonville, Oregon 97070-7777. World Wide Web site: http://www.mentor.com/.

(Mentor Graphics, Mentor, Eldo and Calibre are registered trademarks and Pyxis, Olympus-SoC, LFD, xACT, PERC, nmDRC and nmLVS are trademarks of Mentor Graphics Corporation. All other company or product names are the registered trademarks or trademarks of their respective owners.)

For more information, please contact:
Gene Forte
Mentor Graphics
503.685.1193
gene_forte@mentor.com

Logo - http://photos.prnewswire.com/prnh/20140317/AQ83812LOGO

SOURCE  Mentor Graphics

Photo:http://photos.prnewswire.com/prnh/20140317/AQ83812LOGO
http://photoarchive.ap.org/
Mentor Graphics

Web Site: http://www.mentor.com

Title

Medium Image View Large